B Square scope base

Terry Smith · 04-28-2002, 07:13 PM

Has any of you had any experience with the B Square scope base that mount to the rear sight base?
Also I am having my gunsmith mount Lyman target sights, and cut a target crown on the barrel of my Yugo.
I'll post the results when I get it back.

Terry

colt45 · 04-28-2002, 08:13 PM

Terry,
I too had lyman sights put on my yugo youll love them.
as for the b-square, Hay they keep makeing quality stuff. This isn't one of them. Starters youll need a pistol scope or long eye relief scope because of the distance. They also have a tendency to loosen up makeing it very had to keep a zero even with lock tight.
I would say have your gunsmith bend your bolt handle if needed and go with the weaver #45 and #46 front and back mounts for all modle mausers and some Mill-dot high scope rings.Its a stable combo and with the right scope a deadly combo for the old paper target.

Hans R Colt · 05-08-2002, 12:35 AM

I have one on a k98, and the two main problems I have are:

1. You have to use Red Loctite on the mounting screws to get
them to stay in; even then, sometimes the holes aren't
square(ha ha) to each other, and the mount locks in
crooked(not so B-square, haha).

2. The mount must be angled upwards/elevated no less than 2
degrees above the barrel's centerline or else your shots past
50 yards will be way off...If you have access, get a good
photograph of the Nazi ZF-41 sniper rifle and compare the
scope angle with the barrel's centerline.

05-08-2002, 08:36 AM

I just got a B-Square side chamber mount for my M1.

I am very impressed. YOu all will see it after "Kate" gets her make over, about another week or so.

04-28-2002, 07:13 PM	#1
Terry Smith Registered User Join Date: Apr 2002 Posts: 7	B Square scope base Has any of you had any experience with the B Square scope base that mount to the rear sight base? Also I am having my gunsmith mount Lyman target sights, and cut a target crown on the barrel of my Yugo. I'll post the results when I get it back. Terry Last edited by Terry Smith; 04-28-2002 at 07:16 PM.

04-28-2002, 08:13 PM	#2
colt45 Senior Member Join Date: Mar 2002 Location: Occupied Territories of New York (Buffalo) Posts: 2,898	Terry, I too had lyman sights put on my yugo youll love them. as for the b-square, Hay they keep makeing quality stuff. This isn't one of them. Starters youll need a pistol scope or long eye relief scope because of the distance. They also have a tendency to loosen up makeing it very had to keep a zero even with lock tight. I would say have your gunsmith bend your bolt handle if needed and go with the weaver #45 and #46 front and back mounts for all modle mausers and some Mill-dot high scope rings.Its a stable combo and with the right scope a deadly combo for the old paper target. __________________ "A fear of weapons is a sign of retarded sexual and emotional maturity" -Sigmund Freud, General Introduction to Psychoanalysis "If guns cause crime, all of mine are defective." - Ted Nugent "Self-defense is Nature's eldest law." -John Dryden

05-08-2002, 12:35 AM	#3
Hans R Colt Senior Member Join Date: Mar 2002 Posts: 105	I have one on a k98, and the two main problems I have are: 1. You have to use Red Loctite on the mounting screws to get them to stay in; even then, sometimes the holes aren't square(ha ha) to each other, and the mount locks in crooked(not so B-square, haha). 2. The mount must be angled upwards/elevated no less than 2 degrees above the barrel's centerline or else your shots past 50 yards will be way off...If you have access, get a good photograph of the Nazi ZF-41 sniper rifle and compare the scope angle with the barrel's centerline.

05-08-2002, 08:36 AM	#4
Armorer Guest Posts: n/a	I just got a B-Square side chamber mount for my M1. I am very impressed. YOu all will see it after "Kate" gets her make over, about another week or so.