saftey removal on pa63

jkssr · 09-15-2008, 08:47 AM

cant open it thanks anyways. got the gun appart ok. buffing it looking GOOD

jkssr · 09-15-2008, 12:25 PM

took apart the pa63 and buffed the lower part up shines like crome!! looks great this way. jim

jkssr · 09-15-2008, 12:29 PM

took down my pa63 abd used a high speed buffer on the lower half now looks like crome! a great look for this gun.

saltman101 · 11-09-2008, 09:50 AM

I am a newbie to the site and have previously enjoy following the PA-63 issues. I recently purchased one and have enjoyed it until I was in the process og upgrading the springs and found that mine has no extractor on it. It shoots fine and ejects shells while firing but does not when removing shells from the gun to unload it. They fall out when you pull the receiver back. I guess either it arrived without it or fell out during use. What parts will I need to obtain to replace it and could there be other parts missing also for the extractor mechanism? Thanks all in advance.
Saltman101

240 Coastal · 12-13-2008, 12:03 AM

jkssr,

Any pics you can share of your PA-63 with the frame polished?

Thanks,

Tom

CzechPistol · 12-17-2008, 06:31 PM

Quote:

Originally Posted by 240 Coastal

jkssr,

Any pics you can share of your PA-63 with the frame polished?

Thanks,

Tom

+1!

I think I want to try this, but would like to see someone else's results first

MLN1963 · 09-20-2009, 12:33 AM

Vintovki

Are you saying that you can push the safety plunger into the channel (chase) from the front (ejection port) side? I tried that with mine and I couldn't make that happen no matter how much I tried. It was as if the plunger was too big to fit in the hole. I know that the channel is bored all the way through but something seemed to stop it and make it want to fall into the hole for the extractor. It would certainly be easier if it could go in from the front! I had to manipulate mine in from the rear and that was very time consuming but it went.

Billyz · 10-21-2009, 01:30 AM

thanks for the info fellas. Need to tear mine apart because I see rust behind the extractor.

09-15-2008, 12:29 PM	#23
jkssr Registered User Join Date: Sep 2008 Posts: 5	crome took down my pa63 abd used a high speed buffer on the lower half now looks like crome! a great look for this gun.

11-09-2008, 09:50 AM	#24
saltman101 Registered User Join Date: Nov 2008 Posts: 1	Replacement Extractor Parts PA-63 I am a newbie to the site and have previously enjoy following the PA-63 issues. I recently purchased one and have enjoyed it until I was in the process og upgrading the springs and found that mine has no extractor on it. It shoots fine and ejects shells while firing but does not when removing shells from the gun to unload it. They fall out when you pull the receiver back. I guess either it arrived without it or fell out during use. What parts will I need to obtain to replace it and could there be other parts missing also for the extractor mechanism? Thanks all in advance. Saltman101

10-21-2009, 01:30 AM	#28
Billyz Senior Member Join Date: Mar 2008 Posts: 241	thanks for the info fellas. Need to tear mine apart because I see rust behind the extractor. __________________ COG #47

09-15-2008, 08:47 AM	#21
jkssr Registered User Join Date: Sep 2008 Posts: 5	cant open it thanks anyways. got the gun appart ok. buffing it looking GOOD

09-15-2008, 12:25 PM	#22
jkssr Registered User Join Date: Sep 2008 Posts: 5	took apart the pa63 and buffed the lower part up shines like crome!! looks great this way. jim

12-13-2008, 12:03 AM	#25
240 Coastal Senior Member Join Date: Jun 2008 Posts: 107	jkssr, Any pics you can share of your PA-63 with the frame polished? Thanks, Tom

09-20-2009, 12:33 AM	#27
MLN1963 Senior Member Join Date: Aug 2009 Location: SW OK Posts: 126	Vintovki Are you saying that you can push the safety plunger into the channel (chase) from the front (ejection port) side? I tried that with mine and I couldn't make that happen no matter how much I tried. It was as if the plunger was too big to fit in the hole. I know that the channel is bored all the way through but something seemed to stop it and make it want to fall into the hole for the extractor. It would certainly be easier if it could go in from the front! I had to manipulate mine in from the rear and that was very time consuming but it went.