Mauser Sporter

Devil Dog · 10-27-2002, 05:05 PM

I bought a '98 Mauser sporter at my club range today.
It is a 30-06. Original barrel (I think). It is marked ".30" on the receiver bridge and has the small half circle cut-out on the rear face of the receiver ring. There is a crest on the rec. ring, but I can't make anything from it. It is in a deceant Bishop stock and had the bolt forged low. The receiver was drilled and tapped and had Weaver bases installed. Everything was there...it just needed to be "re-sporterized".
Question: The right side of the receiver ring has the name
"R. FAMAGE 1952" stamped deeply. Is that an original marking or is that just the name of the guy who did the first remodeling job?
Any info would be appreciated.
Thanks,
Gary

TC_NUT · 09-23-2005, 07:04 PM

Gary I have one to mine you have to custom load it uses a 30-06 case and a.312 bullet which is a british 303 round. i dont know what yours may shoot good luck

rebel727 · 09-23-2005, 08:28 PM

best thing to do is make a chamber cast to make sure what caliber it is. Crayons make excellent chamber casts. Plug the barrel where the rifling starts and pour melted crayons in the chamber. When it hardens push it out with a cleaning rod.

rebel727 · 09-23-2005, 08:37 PM

Been doing a lil web searching and from what I find it appears to be a Columbian rebuild and was rechambered in 30-06

lefty o · 09-23-2005, 10:46 PM

i agree with the fact it is probably a colombian redo, or some other south american country. the clue is the little cutout at the rear of the front ring, they did this so the rifle could use stripper clips.

10-27-2002, 05:05 PM	#1
Devil Dog Member Join Date: Mar 2002 Location: Rochester Hills, Michigan Posts: 34	Mauser Sporter I bought a '98 Mauser sporter at my club range today. It is a 30-06. Original barrel (I think). It is marked ".30" on the receiver bridge and has the small half circle cut-out on the rear face of the receiver ring. There is a crest on the rec. ring, but I can't make anything from it. It is in a deceant Bishop stock and had the bolt forged low. The receiver was drilled and tapped and had Weaver bases installed. Everything was there...it just needed to be "re-sporterized". Question: The right side of the receiver ring has the name "R. FAMAGE 1952" stamped deeply. Is that an original marking or is that just the name of the guy who did the first remodeling job? Any info would be appreciated. Thanks, Gary

09-23-2005, 08:28 PM	#3
rebel727 Senior Member Join Date: Mar 2005 Location: Heidelberg, Mississippi Posts: 1,551	best thing to do is make a chamber cast to make sure what caliber it is. Crayons make excellent chamber casts. Plug the barrel where the rifling starts and pour melted crayons in the chamber. When it hardens push it out with a cleaning rod. __________________ North-1 South-0 HALFTIME!

09-23-2005, 08:37 PM	#4
rebel727 Senior Member Join Date: Mar 2005 Location: Heidelberg, Mississippi Posts: 1,551	Been doing a lil web searching and from what I find it appears to be a Columbian rebuild and was rechambered in 30-06 __________________ North-1 South-0 HALFTIME!

09-23-2005, 07:04 PM	#2
TC_NUT Registered User Join Date: Aug 2005 Posts: 2	Gary I have one to mine you have to custom load it uses a 30-06 case and a.312 bullet which is a british 303 round. i dont know what yours may shoot good luck

09-23-2005, 10:46 PM	#5
lefty o Senior Member Join Date: Mar 2002 Location: mn Posts: 4,815	i agree with the fact it is probably a colombian redo, or some other south american country. the clue is the little cutout at the rear of the front ring, they did this so the rifle could use stripper clips.