m91/30 scope mount - Page 3

Mike82 · 03-28-2008, 01:56 PM

ok....you talked me into it..... I TALKY TALKY LIKE THERE'S NO TOMORROWY TOMORROWY....errrr

i forgot how to spell tomorrow....nvm, dictionary says i'm in the good.

SwedeSteve · 03-28-2008, 02:01 PM

LOL!!!! Dont let the brain get ahead of the fingers!

Mike82 · 03-28-2008, 02:08 PM

actually, think my fingers got ahead of brain

Ellsworth · 03-28-2008, 02:08 PM

lol thanks swede, and mike...well.....

It's alright, I was looking up some of the other modification articles and I couldn't see the dovetail on the M44 so I held off until I had confirmation, I figured Swede would come along soon enough.

I got that scope mount on the 44 right now, I've just heard some conflicting reports on it's stability, so I was going to try the dovetail later if the mount started to lose zero.

Pretty soon i'm just going to weld the darn weaver to the barrel and call it good, that ATI mount looks good but I don't trust myself tapping my receiver.

I think the best equal medium is the SKS mount for the shorter site mounts like the M44, it has about 3 fall backs to prevent drift.

Thanks for the discussion mike, learned a lot so far.

SwedeSteve · 03-28-2008, 02:12 PM

Good job Ell! Would like to see a pic when you are finally set up!

Mike82 · 03-28-2008, 02:15 PM

yeah, me too....i learned to not let my fingers talk faster than my brain can correct em lol

also, i wouldn't suggest u try tapping ur own receiver, a gunsmith should be able to do for a decent price....prolly $50 or less if you dont rush him, let him take his time...i find they tend to lower price if you tell em "no rush, just call me when you get it done"

so you have the M44 adapter scope mount? grab ur scope and swing the gun around over ur head, then go out and see if it still shoots straight

next, hold it upside down with scope closest to ground, about 1foot off ground, use a mat so not to scratch floor, then drop it....then go see if it still hits target ROFL

oh yeah, guess what the "great wizard of id-iocy" did....when i left for my 3.5hr drive across state....i forgot to bring my newly smithed 91/30 with me

i knew i forgot something, just couldnt pin-point it till i arrived and someone asked to see my rifle <cries>

i may spend $60 in gas just to go up there again tomorrow and pick it up and run....but how am i going to explain the mileage on company truck -.-

03-28-2008, 01:56 PM	#41
Mike82 Senior Member Join Date: Feb 2008 Location: Vicksburg, Mississippi USA Posts: 487	ok....you talked me into it..... I TALKY TALKY LIKE THERE'S NO TOMORROWY TOMORROWY....errrr i forgot how to spell tomorrow....nvm, dictionary says i'm in the good. __________________ No Trespassing! Violators Will Be Shot! Survivors Will Be Shot Again!

03-28-2008, 02:01 PM	#42
SwedeSteve Senior Member Join Date: Feb 2007 Location: AnchorTown, Alaska Posts: 6,922	LOL!!!! Dont let the brain get ahead of the fingers! __________________ Thank God we don't get as much Government as we pay for! -Will Rogers

03-28-2008, 02:08 PM	#43
Mike82 Senior Member Join Date: Feb 2008 Location: Vicksburg, Mississippi USA Posts: 487	actually, think my fingers got ahead of brain __________________ No Trespassing! Violators Will Be Shot! Survivors Will Be Shot Again!

03-28-2008, 02:12 PM	#45
SwedeSteve Senior Member Join Date: Feb 2007 Location: AnchorTown, Alaska Posts: 6,922	Good job Ell! Would like to see a pic when you are finally set up! __________________ Thank God we don't get as much Government as we pay for! -Will Rogers

03-28-2008, 02:15 PM	#46
Mike82 Senior Member Join Date: Feb 2008 Location: Vicksburg, Mississippi USA Posts: 487	yeah, me too....i learned to not let my fingers talk faster than my brain can correct em lol also, i wouldn't suggest u try tapping ur own receiver, a gunsmith should be able to do for a decent price....prolly $50 or less if you dont rush him, let him take his time...i find they tend to lower price if you tell em "no rush, just call me when you get it done" so you have the M44 adapter scope mount? grab ur scope and swing the gun around over ur head, then go out and see if it still shoots straight next, hold it upside down with scope closest to ground, about 1foot off ground, use a mat so not to scratch floor, then drop it....then go see if it still hits target ROFL oh yeah, guess what the "great wizard of id-iocy" did....when i left for my 3.5hr drive across state....i forgot to bring my newly smithed 91/30 with me i knew i forgot something, just couldnt pin-point it till i arrived and someone asked to see my rifle <cries> i may spend $60 in gas just to go up there again tomorrow and pick it up and run....but how am i going to explain the mileage on company truck -.- __________________ No Trespassing! Violators Will Be Shot! Survivors Will Be Shot Again! Last edited by Mike82; 03-28-2008 at 10:15 PM. Reason: Automerged Doublepost

03-28-2008, 02:08 PM	#44
Ellsworth Member Join Date: Mar 2008 Location: Cheney, Washington Posts: 86	lol thanks swede, and mike...well..... It's alright, I was looking up some of the other modification articles and I couldn't see the dovetail on the M44 so I held off until I had confirmation, I figured Swede would come along soon enough. I got that scope mount on the 44 right now, I've just heard some conflicting reports on it's stability, so I was going to try the dovetail later if the mount started to lose zero. Pretty soon i'm just going to weld the darn weaver to the barrel and call it good, that ATI mount looks good but I don't trust myself tapping my receiver. I think the best equal medium is the SKS mount for the shorter site mounts like the M44, it has about 3 fall backs to prevent drift. Thanks for the discussion mike, learned a lot so far.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode