Reply
 
Thread Tools
Old 11-19-2009, 07:32 PM   #21
Firearm Enthusiast
 
Join Date: Nov 2009
Location: NM
Posts: 15
A little off topic, but here's an interesting find.

Refit your VZ.24 with a brand new stock

VZ24 Stocks

50 pristine, $35 minor dings
MountainDon is offline   Reply With Quote
Old 11-20-2009, 08:34 PM   #22
Firearm Enthusiast
 
Join Date: Nov 2009
Location: NM
Posts: 15
I decided to take some pictures today and post them. I've cleaned up most o the cosmoline. There are still amounts to be removed rom the handguard. It's apparent in some o the photos. Just forward o the receiver the handguard wood is still darker in color. If I hit that area with a heat gun cosmo rises rom the wood pores. Same thing near the foreend of the handguard. After I play with it at the club range I want to dismantle it and clean the wood proper, then refinish.











MountainDon is offline   Reply With Quote
Old 11-20-2009, 10:27 PM   #23
Firearm Enthusiast
 
AFC-Snowman's Avatar
 
Join Date: Nov 2009
Location: everywhere.
Posts: 81
Thumbs up Smoking...

Hmm....Looks to my untrained eyes like that is a pretty good deal then!

Congrats!
AFC-Snowman is offline   Reply With Quote
Old 11-21-2009, 04:02 PM   #24
Firearm Enthusiast
 
Join Date: Nov 2009
Location: NM
Posts: 15
It's a good shooter. The sights are factory set starting at 300 meters. Once I figured out how high it was shooting at 100 yards I could get them in the black. I 2 - 3 inch groups when I was careful, which for my eyes is darn good. That was with 150 gr Romanian surplus ammo made in 1972. Fifty-five rounds of that. Next I ran 35 Yugoslavian 196 gr surplus, made Nov 1956. I could feel the difference in my shoulder. It shot a bit higher and did about the same on groups. Every single round fired with no problems.

To end the rifle session I shot 5 Wolf brand 196 gr, new non-corrosive boxer primed load and 5 Sellier & Bellot 196 gr. For all I know those are the same stuff; they produced very similar 2 inch groups, better than the mil-surplus stuff. More $$ too, mind you.

In case anyone is interested and for what it's worth, the Yugo stripper clips are much nicer than the Romanian. Both the Romanian and the Yugo came loaded on 5 shot strippers, but the Yugo slid into the magazine much easier. With the Romanian I was at the point where it seemed easier, less trouble, to remove the ammo from the stripper and load the rile one at a time. Maybe it's me? But the Yugo slipped into the magazine with real ease.

Now I have to decide if I want to buy a spam can of surplus, or buy more of the Wolf or S&B, save the reloadable brass and go that way.

One thing I'll admit to is the Romanian 150 gr is much easier on the shoulder if all you are doing is killing paper.

I'm also thinking of trying a Mojo aperture sight. It mounts in place of the stock rear sight so the firearm can be returned to original condition and leave no trace.
MountainDon is offline   Reply With Quote
Old 12-15-2009, 08:27 PM   #25
Firearm Enthusiast
 
Join Date: Nov 2009
Location: NM
Posts: 15
Last night I tore it down. There was a fair amount of cosmo still between the receiver/barrel and the stock and handguard. The cosmo had so permeated the handguard it would weep more every time it got warm.



I used purple power cleaner concentrate and hot water to clean the stock. I ran the handguard through the dishwasher and that cleaned all the gunk out of it.



I have a question. Can anyone tell me the purpose of the two dovetailed inserts in the handguard? Here's a closeup of one.



The dark lines appear to be epoxy glue. There were a couple other spots and they came off easily. The water raised the grain a little, but it was knocked down easily with a little 180 grit paper. Next I'll get out the really fine sandpaper and get ready to refinish the wood.
MountainDon is offline   Reply With Quote
Old 12-20-2009, 09:07 PM   #26
Firearm Enthusiast
 
Join Date: Oct 2009
Posts: 112
Quote:       Originally Posted by MountainDon View Post
If I hit that area with a heat gun cosmo rises rom the wood pores. Same thing near the foreend of the handguard.



would i be able to use a hairdryer as a heat gun?
assaultrecon28 is offline   Reply With Quote
Old 12-21-2009, 12:33 AM   #27
Firearm Enthusiast
 
AFC-Snowman's Avatar
 
Join Date: Nov 2009
Location: everywhere.
Posts: 81
^^^ depends on two things lol. quality of hair dryer (i.e. how hot it gets) and quality of heat gun were comparing it to! Ive used some hair dryers in the manner you describe quite well, and some "heat guns" in the same manner that were terrible! So...just give it a try!
AFC-Snowman is offline   Reply With Quote
Old 12-24-2009, 04:22 PM   #28
Firearm Enthusiast
 
Join Date: Nov 2009
Location: NM
Posts: 15
My heat gun is rated at 1000 watts. I got it years ago from a hobby dealer when I was building R/C aircraft. It seems to throw more heat than my wife's hair dryer gun. Go figure that.


What with this , that and another I've yet to stain/finish the wood.
MountainDon is offline   Reply With Quote
Old 01-09-2010, 07:48 PM   #29
Firearm Enthusiast
 
Join Date: Nov 2009
Location: NM
Posts: 15
Okay, the VZ24 was totally cleaned up and the wood refinished. Pictures below. Some may argue that I should not have refinished it, but I say it's not exactly a rare rifle so it doesn't bother me. I got a genuine VZ24 bayonet for Christmas.





MountainDon is offline   Reply With Quote
Old 01-10-2010, 01:30 AM   #30
Firearm Enthusiast
 
AFC-Snowman's Avatar
 
Join Date: Nov 2009
Location: everywhere.
Posts: 81
ooh....

very pretty! you have got to share your mixture that you used to refinish it....
AFC-Snowman is offline   Reply With Quote
Old 01-10-2010, 03:05 AM   #31
Firearm Zealot
 
ArkansasHunter's Avatar
 
Join Date: Mar 2007
Location: Buck Snort, Arkansas.
Posts: 20,563
MountainDon You did a fantastic refinish job on the stock what stain did you use ?
__________________
IN GOD WE TRUST
NRA MEMBER
ArkansasHunter is offline   Reply With Quote
Old 01-15-2010, 02:21 AM   #32
Firearm Aficionado
 
Join Date: Jul 2008
Location: Down south.
Posts: 894
Thumbs up

Beautiful rifle:

You guys are lucky that such Mausers have sling swivels instead of the Yugo 48A version which is often missing (don't know the name for the leather piece on both sides of the stock's slot).
Laufer is offline   Reply With Quote
Reply

Gun & Game - The Friendliest Gun Forum on the Internet > General > The Powder Keg

Tags
aim, vz24

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -5. The time now is 10:37 AM.




Recent Discussions

Connect with us!
Advertisement



"It don't cost nuthin' to be nice." -- Mike West